Tesk
language
中国
韩国
韩国
韩国
韩国
韩国
English/Language
language
中国
韩国
韩国
韩国
韩国
韩国

搜索
Search
img
NEWS NEWS

Submersible borehole pump for 6 inch manufacturers take you to understand what needs to be paid attention to in the installation and operation of submersible pumps

  • Categories:NEWS
  • Author:
  • Origin:
  • Time of issue:2022-06-20 16:55
  • Views:

(Summary description)The manufacturer of Submersible borehole pump for 6 inch tells you to analyze the use environment, the submersible pump needs to be equipped with a reliable power supply, the drop between the outlet pipe and the water surface of the pool should be lower than the head.

Submersible borehole pump for 6 inch manufacturers take you to understand what needs to be paid attention to in the installation and operation of submersible pumps

(Summary description)The manufacturer of Submersible borehole pump for 6 inch tells you to analyze the use environment, the submersible pump needs to be equipped with a reliable power supply, the drop between the outlet pipe and the water surface of the pool should be lower than the head.

  • Categories:NEWS
  • Author:
  • Origin:
  • Time of issue:2022-06-20 16:55
  • Views:
Information

The manufacturer of Submersible borehole pump for 6 inch tells you to analyze the use environment, the submersible pump needs to be equipped with a reliable power supply, the drop between the outlet pipe and the water surface of the pool should be lower than the head, and the selection of the water source should also be relatively clean.

Cheap Submersible borehole pump for 6 inch factory
The manufacturer of Submersible borehole pump for 6 inch tells you that after the submersible pump starts and starts working, it is necessary to monitor the change of water level to ensure the normal operation of the submersible pump. When the submersible pump runs for 5 hours, it is necessary to stop and quickly measure the insulation resistance, and the measured value shall not be lower than 0.5MΩ. The manufacturer of Submersible borehole pump for 6 inch tells you that the working point of the submersible pump is pre-set. Because the axial force of the working point is moderate, efficient, economical and reliable, it cannot be replaced at will.
When it runs for 8 hours, it is necessary to check the submersible pump to check whether all instruments and meters can operate normally, whether the nodes of the circuit are heated, whether the sound emitted is abnormal, and whether the current value during operation is higher than The rating of the motor is large. The manufacturer of Submersible borehole pump for 6 inch tells you to be as careful as possible during the loading and unloading process of the submersible pump to avoid damaging the concentricity of the unit and to avoid damaging the cable insulation.
The manufacturer of Submersible borehole pump for 6 inch tells you to place the submersible pump vertically before installation, and open both the vent hole and the water injection hole. It should be noted that the two water plugging holes should be opened and filled with water, and the two should be tightened and observed. Whether there is water leakage. Remove the upper casing of the submersible pump to expose the impeller, and turn it by hand to see if it is flexible. Pull the impeller in the direction of the bearing and observe the total displacement.
The manufacturer of Submersible borehole pump for 6 inch tells you to combine the motor with the coupling, the shaft head of the motor and the shaft head of the submersible pump should be closely connected, and there should be no gap; observe the gap between the upper and lower displacement of the impeller, it should be within the total displacement the middle position; then drill the top screw hole, and tighten the top screw to install the upper shell. It is necessary to move the coupling with a pry bar to make it run for one week. It should be turned flexibly to be considered as qualified, and the filter screen and the wire protection groove box should be installed.
The manufacturer of Submersible borehole pump for 6 inch tells you that if the cable needs to be tied to the lift pipe with insulating ties, wire must not be used. The installation process of the submersible pump is interlinked, each link plays a decisive role, and each link needs to be carried out in strict accordance with the standards, and must not be sloppy. It is not only the safety of machine use that is involved, but also the safety of operators.
The above are some of the things that the Submersible borehole pump for 6 inch manufacturer tells you to pay attention to when installing and operating the submersible pump, I hope it will help you!

Keyword:

Scan the QR code to read on your phone

COPYRIGHT Zhejiang Nanyuan Pump Industry Co. Ltd.      浙ICP备2020030285号-1